For the first time configuration:

 First, plug the clip to the cell phone.
 While the led is blinking insert the phone number you want the NuvoGuard to dial \SMS to when it will sense a movement.
 The led will blink for about 10 seconds. During this time it will allow you to configure the NuvoGuard or position it as an alarm (if it was already pre-configured).

User should make sure to complete programming before the led stop blinking .
Configuring the number will be as a standard outgoing call in the following format : 

     # # 1 # 0 5 2 4 4 8 5 1 5 7(SEND)  

If you want to be notified with a following SMS dial the following (adding * after the number):

   # # 1 # 0 5 2 4 4 8  5 1 5 7 * (SEND)  

After pressing the SEND button the call will hang off automatically .

If you want to change the number that was already configured, simply repeat the previous actions but this time with a different number .

 * Make sure you configure the NuvoGuard before the led will stop blinking.

 After the NuvoGuard detected a movement and sending a call\SMS to your predefined umber - the system will enter an idle mode for 15 minutes, in which it will wait for your  call. 
 During these 15 minutes the system will not be sensitive to any movements, but you'll be able to call the device and listen with no one to notice.
 After hang up the call to the device – the system will reactivate again.
 It is not mandatory to call back to the NuvoGuard's cell phone.

 In order to listen with no one to know - you just dial to the NuvoGuard's phone number.

• From the moment the NuvoGuard has detected the movement, the system will move to a waiting mode as any other alarm system. during this time you will be able to disarm the alarm by unplugging the clip or by typing a deactivation code : # # 3 # 0 (SEND).
  You will be able to activate it again by typing the activation code : # # 3 # 1 (SEND) or plug the clip back if it was unplugged.
• All definitions are stored in to the NuvoGuard memory even after it was unplugged and there is no need to configure it again.
• There is an option to configure another phone number that will receive only an SMS.
  To allocate a number for cell # 2 repeat the first configuration step like you did for cell # 1 but change it to 2:
   # # 2 # 0 5 2 4 4 8 5 4 5 4 (SEND)
• In order to delete a number that was allocated for a certain cell, you need to program 9999999 as the preferred number as follows:  # # 2 # 9 9 9 9 9 9 9 (SEND) - this will delete cell # 2.

NuvoGuard Clip Pro with remote activation - Instructions:

 CLIP PRO Model - IMPORTANT NOTICE:

 In the pro model - when first pluging the clip, the led will power on for several seconds, then it will power off, and then power on again for about 30 seconds. during these 30 seconds, insert the number that you want the clip to dial to and then press send\Dial (for example :    # # 1 # 0 5 2 4 4 8 5 1 5 7(SEND)

 IN THIS MODEL YOU MUST CALL FROM PRIVATE NUMBER IN ORDER TO PERFORM THE SILENT LISTENING ( YOU CAN DO THAT FROM ANY PHONE 
 NUMBER  just make sure the dialed number is recognized as private ! )

 Activating \ Deactivating the NuvoGuard from remote:

 IMPORTANT:
 These two  operation MUST be done from the number you've configured your NuvoGuard to dial to.

 Deactivation:

 All you have to do in order to deactivate the NuvoGuard is to dial the cell phone that the NuvoGuard is plugged to. The call will then automatically hang up, and the NuvoGuard 
 will not be sensitive to any movement.

 Activation:

 All you have to do in order to activate the NuvoGuard is to dial the cell phone that the NuvoGuard is plugged to the same you did in order to deactivate it. The call will then  
 automatically hang up by the NuvoGuard, and the NuvoGuard will immediately dial back to your number in order to notify you the alarm is set.

NuvoGuard Clip (All models) - Advanced settings:

 In order to produce more from your NuvoGuard here are some more advanced configurations:

 You have the option to change the NuvoGuard clip level of sensitivity.
 Changing these settings is for advanced users only, This is the format (from left to right) : # # * # A B C D E  

 A = The amount of time ( seconds ) between the start of the alram call till it ends.

 B = The number of movements you'd like to mesure before sending the call.

 C = The amount of time in which the the NuvoGuard mesure the number of movements.

 D = The state of the led (1=enabled, 0= Disabled).

 E = NuvoGurard sensor model (For the clip configuration it is NC and the default value is 0)

 The NuvoGurad's is programmed with the default parameters:

 # # * # 7 1 2 0 0 (SEND)   which means that the NuvoGuard clip will initiate a call that will last seven seconds (it will ring for
 seven seconds ) after it will recognize one movement in a measured time of two seconds. The led during idle mode (the
 Clip is waiting to detect a movement) will be disabled