For the first time configuration:

 First of all - connect the battery or any external power supply to the voltage connector.
 Now, Plug the connector at the end of the cable to the cell phone.
 User have about 40 seconds to enter the phone number he wants the NuvoGuard to dial \SMS to when it will sense a movement.
 During this time it will allow you to configure the NuvoGuard or position it as an alarm (if it was already pre-configured).

 User should make sure to complete programming in 40 seconds.
 Configuring the number will be as a standard outgoing call in the following format:

   # # 1 # 0 5 2 6 3 8 5 1 5 7(SEND)

 If you want to be notified with a following SMS, dial the following (adding * after the number):

   # # 1 # 0 5 2 6 3 8  5 1 5 7 * (SEND)

 After pressing the SEND button the call will hang off automatically.
 To complete the configuration step, Un plug the battery and then plug it again.

 If you want to change the number that was already configured, simply repeat the previous actions but this time with a different number.

 After the NuvoGuard Hme detected a movement and sending a call \ SMS to your predefined number - the system will enter an idle mode for 15 minutes, in which it will wait for your call. 
 During these 15 minutes the system will not be sensitive to any movements, but you'll be able to call the device and listen with no one to notice as the phone will automatically answer the phone with no 
 ringing.
 After ending the listening call to the NuvoGuard – the system will reactivate again.
 It is not mandatory to call back to the NuvoGuard's cell phone and it will activate again automatically after 15 minutes.

 In order to listen with no one to know - you just dial to the NuvoGuard's phone number.

• All definitions are stored in to the NuvoGuard memory even after it was unplugged and there is no need to configure it again.
• There is an option to configure another phone number that will receive only an SMS.
  To allocate a number for cell # 2 repeat the first configuration step like you did for cell # 1 but change it to 2:
   # # 2 # 0 5 2 6 3 8 5 4 5 4 (SEND)
• In order to delete a number that was allocated for a certain cell, you need to program 9999999 as the preferred number as follows:  # # 2 # 9 9 9 9 9 9 9 (SEND) - this will delete cell # 2.

Remote activation \ Deactivation - Instructions:

 IMPORTANT NOTICE:

 IN THIS MODEL YOU MUST CALL FROM PRIVATE NUMBER IN ORDER TO PERFORM THE
 SILENT LISTENING ( YOU CAN DO THAT FROM ANY PHONE NUMBER ! )

 Activating \ Deactivating the NuvoGuard from remote:

 IMPORTANT:

 These two operations MUST be done from the number you've configured your NuvoGuard to dial to.

 Deactivation:

 All you have to do in order to deactivate the NuvoGuard, is to dial to the cell phone number that the NuvoGuard is plugged to. The call will then automatically hang up, and the NuvoGuard will not be sensitive 
 to any movement.

 Activation:

 All you have to do in order to activate the NuvoGuard, is to dial to the cell phone number that the NuvoGuard is plugged to the same you did in order to deactivate it. The call 
 will then automatically hang up by the NuvoGuard, and the NuvoGuard will immediately dial back to your number in order to notify you the alarm is set.

NuvoGuard Home - Advanced settings:

 In order to produce more from your NuvoGuard here are some more advanced configurations:

 You have the option to change the NuvoGuard Clip\Home level of sensitivity.
 Changing these settings is for advanced users only, This is the format (from left to right) : # # * # A B C D E  

 A = The amount of time (seconds) between the start of the alram call till it ends.

 B = The number of movements you'd like to mesure before sending the call.

 C = The amount of time in which the the NuvoGuard mesure the number of movements.

 D = The state of the led (1=enabled, 0= Disabled).

 E = NuvoGurard sensor model (For the clip configuration it is NC and the default value is 1)

 The NuvoGurad's is programmed with the default parameters:

 # # * # 6 3 4 0 1 (SEND)   which means that the NuvoGuard clip will initiate a call that will last six seconds (it will ring for
 six seconds ) after it will recognize three movements in a measured time of four seconds. The led during idle mode (the
 Clip is waiting to detect a movement) will be disabled.